ScoobyNet.com - Subaru Enthusiast Forum - View Profile: MartynJ



MartynJ MartynJ is offline

Scooby Regular

Visitor Messages

Showing Visitor Messages 1 to 10 of 14
  1. Chriskarl22
    21 March 2017 10:39 PM
    Chriskarl22
    Thanks for the rapid reply Martyn. Sorry Ive taken so long to reply I assumed id get an automated email when you replied but I didnt. Does that price include re-honing the bore or any machining should oversize pistons be needed? My engine is running fine but just to be safe Im just trying to know consider any other costs. Also would I be correct in assuming I would need a head stud conversion for my desired power? Do you still stock the s206 turbo and if so how much would this be or whatever turbo you advise for this sort of power if purchased at the same time as the short block build? Finally is the stock ecu capable of running that sort of power, I assume it would require maf delete if its even possible on the standard Ecu. Sorry about all the questions but after hours of research on forums so many people give so many differing results Id rather just hear it from someone I can guarantee is in the know.
  2. Chriskarl22
    20 March 2017 03:53 PM
    Chriskarl22
    Hi MartynJ, I have found an old page in which you say you sell the famed engine tuner 2.1 stroker short engines for 2150 inc vat but it dates from 2010...I know costs have increased so I assume this price is also outdated. How much does this stand at now? Also is this on an exchange basis? Secondly obviously it is depending on supporting modifications but what sort of power do you advise these engines not to be taken over... I am hoping to be running methanol if also if that helps and aiming for low to mid 500's.
    If you would rather reply to my email as some traders prefer its [email protected]
    Thanks for your time
  3. krajik17
  4. RoyPinhey
    30 October 2016 06:11 PM
    RoyPinhey
    Hi martyn, I've just picked up another impreza but this time a blob eye wrx wagon. I'm looking to get a billet SC36/38 turbo and bolt it on . . Without sounding to naive (as I've been away from subs for a while) what else will I need to get the 350bhp+ they are rated for? Obviously would bring to you for mapping as I have with the last few
  5. harrygreen
    12 December 2014 08:13 PM
    harrygreen
    Thanks martyn top job today
  6. Chris33
    27 February 2014 06:45 PM
    Chris33
    Hi Martin how much do you guys charge to set up my recently purchased gc8 with simtek ecu already installed but previous owner did some mods to it and not had it remapped yet thanks
  7. toyney83
    22 February 2012 06:47 PM
    toyney83
    Hi, im after a little help. Im trying to spec my engine build, i've got a wedding im paying for at the minute but come august then im hoping to crack on with my build. I have a 2005 uk sti with standard heads and a 2.5 bottom end. Im planning on running about the 460-500 mark but want to use the 2.5 as i enjoy the lazy drive and the torque it delivers. Im thinking acl or cosworth bearings, carrillo rods and cp pistons. A couple of questions i'd like to raise is which gaskets should i use as i know hg failure on the 2.5 can be common and also would the block need sleeving with such as darton sleeves as i understand the original liners are quite thin? I'd like your lads to do the build for me if thats possible as im always hearing good things about you. What sort of cost am i looking at, if i supply the materials? Thanks for your time
    Mike Toyne
  8. MartynJ
    15 January 2012 11:37 AM
    MartynJ
    Yes, just stay off the gas and stick to the speed limit.
  9. stuward
    15 January 2012 11:27 AM
    stuward
    Still ok to drive tho as I'm in warminster
  10. MartynJ
    15 January 2012 10:13 AM
    MartynJ
    Sounds like the clutch is slipping big time, drop it in when you can and we'll have a look.

About Me

  • About MartynJ
    Location
    Enginetuner Plymouth for 4wd RR Mapping Apexi Ecutek Alcatek Proper Garage More than just a laptop!

Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: 21 July 2017 11:08 AM
  • Join Date: 17 January 2006
  • Referrals: 0

Friends

Showing Friends 1 to 10 of 13

All times are GMT +1. The time now is 01:32 PM.