how to fit knocklink LEDs into center gauge pod? - ScoobyNet.com - Subaru Enthusiast Forum

Notices

how to fit knocklink LEDs into center gauge pod?

Reply

 
 
 
Old 04 December 2018, 06:49 PM
  #1  
speirsy
Scooby Regular
Thread Starter
 
Join Date: Apr 2005
Location: Scotland
Posts: 209
Default how to fit knocklink LEDs into center gauge pod?

Hi all, looking for a bit of advice if possible. I'm looking to fit a knocklink but extend the knocklink LEDs into my gauge pod to hide the ugly box making the LED location subtle and closer to my line of vision when driving. I was sure I read a thread years ago on Scoobynet that covered how to extend the knocklink LED and plumb them into a center pod and bits required to do this, but can't seem to dig anything up showing how to do this? Has anyone done this to their Scoob pod, and if so what Maplin bit and bobs were needed?

Cheers,
Speirsy
speirsy is offline  
Reply With Quote
Old 04 December 2018, 07:18 PM
  #2  
Don Clark
Scooby Regular
 
Don Clark's Avatar
 
Join Date: Feb 2003
Location: Harpenden
Posts: 4,627
Default

A couple of links on this thread but pictures look to be missing

https://www.scoobynet.com/lighting-a...-is-it-to.html
Don Clark is offline  
Reply With Quote
Old 05 December 2018, 11:35 AM
  #3  
alcazar
Scooby Regular
iTrader: (2)
 
Join Date: Jun 2002
Location: Rl'yeh
Posts: 40,586
Default

Not difficult but fiddly. You need some multicore cable, such as telephone cable, one corew for each LED plus a return.

Once you get the KL box open, you'll see the LEDs, each one needs un-soldering, and a separate wire to each from the FEED on the KL, with the return via a common wire. You'll see which this is.
Do make sure you observe LED polarity...the lead on the LED attached to feed must remain attached to feed, not transposed, or you might be looking for new LEDs. I've done this with both my KL and my LL.

Mine are grouped around the fuel pressure gauge high up on the A pillar, so nicely at eye level. Those and the FP gauge linked to the boost gauge have saved the car at least once.
alcazar is offline  
Reply With Quote
Old 05 December 2018, 04:52 PM
  #4  
speirsy
Scooby Regular
Thread Starter
 
Join Date: Apr 2005
Location: Scotland
Posts: 209
Default

Gents thanks for the passing on the guides and experiences on how to do this.
That's a pain that the uklegacy.com guides doesn't have any photos anymore as it looked to be a good detailed guide and I would have liked to see how he used the floppy drive cable for doing this. I also had a look on the P1woc site and found a good guide, even stating part numbers for required parts from Maplins. I think this may have been the guide I thought I had read on SN.

I've opened up my KL and had a look at what needs doing and now know how to tackle this job. Still waiting for my center pod to arrive and I'll need to buy a soldering iron etc so expect to get into this little project in a week or two. All going well I may even put up an idiots guide to doing this as a lot of the old guides have dead links, or obsolete website or missing pictures (as used Photobucket)

Will holler back if I run into any bother once I get going on this.

Cheers.
speirsy is offline  
Reply With Quote
Old 05 December 2018, 08:50 PM
  #5  
scooby kid
Scooby Regular
iTrader: (6)
 
Join Date: Jul 2010
Location: hastings
Posts: 1,430
Default

Can a knocklink still be bought ?
scooby kid is offline  
Reply With Quote
Old 06 December 2018, 01:22 AM
  #6  
ossett2k2
Scooby Regular
iTrader: (9)
 
ossett2k2's Avatar
 
Join Date: Jan 2007
Location: Leeds
Posts: 6,090
Default

Originally Posted by scooby kid View Post
Can a knocklink still be bought ?
looks like it can...
http://www.mocomracing.com/product_details.asp?id=185
ossett2k2 is offline  
Reply With Quote
 
 
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
morpheous
General Technical
18
03 November 2005 10:57 PM
n one
General Technical
4
19 September 2004 07:53 PM
Spenny_B
General Technical
13
30 June 2004 05:44 PM
Paul_M
General Technical
6
03 July 2003 08:06 PM


Thread Tools
Search this Thread
Quick Reply: how to fit knocklink LEDs into center gauge pod?


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.