Blobeye headlight help needed (North Hampshire) - ScoobyNet.com - Subaru Enthusiast Forum



Blobeye headlight help needed (North Hampshire)

Reply
 
 
 
Thread Tools Search this Thread
Old 26 September 2017, 04:13 PM   #1
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default Blobeye headlight help needed (North Hampshire)

Back at the start of March, I had an unfortunate run in with a pheasant, which smashed my passenger side headlight.

I bought some replacements, which had no levelling motor, and as it turns out, the adjusters don't work, so I have my passenger side pointing to the ground, and the driver's side up into oncoming traffic. I have not been using them since then (luckily I drive in daytime only).

I still have my old headlight units, with the motors attached. A friend helped me fit the new headlights, but we weren't sure about removing the levelling motor from the old units to transfer it over, and didn't want to force it, so have left them there

My questions are:
- Are the adjusters in any way linked to the levelling motor?
- Could transferring the motors over fix the adjusters?
- How do you remove the motors safely?
- Is anyone near Basingstoke who can help? (Mechanically ignorant, here)

I've looked on ebay but can't find any suitable replacement blobeye units, and I don't fancy paying the 400 per side for Subaru to supply and fit replacements.
DCTim is offline   Reply With Quote
Old 26 September 2017, 05:36 PM   #2
bobbyd182
Scooby Regular
iTrader: (2)
 
Join Date: Oct 2014
Location: lancashire
Posts: 151
Default

https://www.buycarparts.co.uk/subaru...adlight-insert

Found these.

Not sure why left and right are completely different prices..
bobbyd182 is offline   Reply With Quote
Old 26 September 2017, 05:50 PM   #3
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Aah, good spot. Says it's for the electric levelling, but doesn't say if it has the motor included. OR am I blind a blind thicko again?
DCTim is offline   Reply With Quote
Old 27 September 2017, 11:59 AM   #4
alcazar
Scooby Regular
iTrader: (2)
 
Join Date: Jun 2002
Location: Rl'yeh
Posts: 39,865
Default

You can exchange motors. I've done it on some classic ones. DO have the right type of, and a decent screwdriver. I removed the screws holding the motors and replaced them with stainless ones off ebay, since all had the heads rusted to hell...hence the need for the good screwdriver.
alcazar is offline   Reply With Quote
Old 27 September 2017, 02:56 PM   #5
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Yeah. I'm just a bit wary of replacing them. My friend and I tried to remove them from my old headlight unit but couldn't work out how to do it safely or without breaking anything.
DCTim is offline   Reply With Quote
Old 27 September 2017, 03:00 PM   #6
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Ordered one of those headlights, though. We'll see what arrives
DCTim is offline   Reply With Quote
Old 28 September 2017, 05:51 PM   #7
WRXrowdy
Scooby Regular
iTrader: (2)
 
Join Date: Nov 2010
Posts: 1,037
Default

Quote:
Originally Posted by bobbyd182 View Post
https://www.buycarparts.co.uk/subaru...adlight-insert

Found these.

Not sure why left and right are completely different prices..
It's not unusual for items on opposing sides of vehicles to have differing prices, normally the near side being the more expensive, as it's more common they are damaged due to branches, curbs etc.
WRXrowdy is offline   Reply With Quote
Old 03 October 2017, 08:04 PM   #8
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Got the headlight delivered. Taiwanese aftermarket. Doesn't come with a headlight motor, though. I'm struggling to find a guide/video on removing the old motor and fitting it to the new headlight. Does anyone know where to find one?

Also, how am I supposed to adjust the aim while the units are in situ? The adjusters are blocked by a reservoir and some other piping. There's a gap in the top to look like a special geared tool can get in to do it, but I've no idea what that tool is
DCTim is offline   Reply With Quote
Old 03 October 2017, 08:43 PM   #9
Don Clark
Scooby Regular
 
Don Clark's Avatar
 
Join Date: Feb 2003
Location: Harpenden
Posts: 3,892
Default

Don Clark is offline   Reply With Quote
Old 03 October 2017, 08:47 PM   #10
Don Clark
Scooby Regular
 
Don Clark's Avatar
 
Join Date: Feb 2003
Location: Harpenden
Posts: 3,892
Default

Blob headlight without motor



With motor



looks as if its attached by just the three screws
Don Clark is offline   Reply With Quote
Old 04 October 2017, 08:49 PM   #11
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Aah. Yeah I didn't notice the bolt head for adjusting (on the red arrow). I don't have anything to use on the other one. The unit needs the motor to adjust the blue arrow. There's nothing there. I'm guessing the motor will fit in there and then be adjusted from that.

So back to me looking for a motor removal/fitting guide

Edit: Sorry for sounding like a complete dumbarse......but I am. I don't do mechanical stuff at all. I just drive the car

Last edited by DCTim; 04 October 2017 at 08:50 PM. Reason: Dumbarse apology
DCTim is offline   Reply With Quote
Old 04 October 2017, 09:44 PM   #12
Don Clark
Scooby Regular
 
Don Clark's Avatar
 
Join Date: Feb 2003
Location: Harpenden
Posts: 3,892
Default

Quote:
Originally Posted by DCTim View Post
Aah. Yeah I didn't notice the bolt head for adjusting (on the red arrow). I don't have anything to use on the other one. The unit needs the motor to adjust the blue arrow. There's nothing there. I'm guessing the motor will fit in there and then be adjusted from that.

So back to me looking for a motor removal/fitting guide

Edit: Sorry for sounding like a complete dumbarse......but I am. I don't do mechanical stuff at all. I just drive the car
Sounds as if you should be looking for someone to do it for you
Don Clark is offline   Reply With Quote
Old 07 October 2017, 08:28 PM   #13
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Got it in one, Don.
DCTim is offline   Reply With Quote
Old 11 October 2017, 11:55 PM   #14
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

So the adjusters do work on the new headlights, they're just VERY slow. Still looking for a guide on how to remove/refit the headlight motors from my old units into the new ones. I can't find anything anywhere, though
DCTim is offline   Reply With Quote
Old 12 October 2017, 09:07 AM   #15
alcazar
Scooby Regular
iTrader: (2)
 
Join Date: Jun 2002
Location: Rl'yeh
Posts: 39,865
Default

Should be straightforward.

Remove from old unit.
Remove cover from fitting point in new unit. Check that the parts inside match up.
Fit to new unit.

It would be a good idea to ensure it's in the middle of it's travel before removing.
alcazar is offline   Reply With Quote
Old 16 December 2017, 01:12 PM   #16
TECHNOPUG
Scooby Regular
iTrader: (1)
 
Join Date: Nov 2014
Location: Tetbury
Posts: 1,159
Default

Apologies for bumping this thread but I think my query is relevant...

I have a set of JDM HID Blob headlights to fit. They didn't come with adjusting motors. I'm unsure whether they had been removed or whether they were never fitted (I have some documentation to suggest that possibly not all headlights came with the motors as standard?). Anyway, if they had come with motors, they would have been with the 6-pin connector, which would need a new custom loom to connect to the 4-pin EUDM switch.

However, as they have no motors, can I swap the motors from my current EUDM headlights - are they a straight swap and do they include the connector (or is is built into the headlight unit)?
TECHNOPUG is offline   Reply With Quote
Old 16 December 2017, 04:33 PM   #17
TECHNOPUG
Scooby Regular
iTrader: (1)
 
Join Date: Nov 2014
Location: Tetbury
Posts: 1,159
Default

Well in theory it should work....

Managed to finally remove 3 screws holding the motor to the headlight. The last one had predictably rusted solid. Cut the head of the screw off as it only threads into the headlight, not the motor housing, so I could then pull the motor off. Somehow though it had managed to rust to plastic.....so cut it off at the bottom. So now it's free, how to I actually remove the motor from the headlight? There is a threaded bar that connects the motor to the levelling mechanism - just this just pull off - does it have a ball/cup at the end?
TECHNOPUG is offline   Reply With Quote
Old 17 December 2017, 04:48 PM   #18
TECHNOPUG
Scooby Regular
iTrader: (1)
 
Join Date: Nov 2014
Location: Tetbury
Posts: 1,159
Default

So it is a ball a cup. Always wary of applying force to car plastics but it popped out eventually.

I'm somewhat confused as to all the threads I have read about custom looms and JDM switches in order to get the 6-pin JDM motor to work with the 4-EUDM plug. When all you have to do is swap the motors over....I can only assume that people are selling their EUDM with the motors attached or have no motors currently but the EUDM switch/plug is present?
TECHNOPUG is offline   Reply With Quote
Old 20 December 2017, 10:23 PM   #19
DCTim
Scooby Regular
Thread Starter
 
Join Date: Apr 2007
Posts: 208
Default

Aah, thanks for the instructions dude. I'll have to get together with a friend and see what we can do.
DCTim is offline   Reply With Quote
Old 21 December 2017, 12:28 AM   #20
TECHNOPUG
Scooby Regular
iTrader: (1)
 
Join Date: Nov 2014
Location: Tetbury
Posts: 1,159
Default

Both motors had the same screw rusted solid. You may get lucky but assume that you'll have to cut it off.
TECHNOPUG is offline   Reply With Quote
 
 
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT +1. The time now is 05:39 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: