Getting a power cable into the boot - how? - ScoobyNet.com - Subaru Enthusiast Forum

Go Back  ScoobyNet.com - Subaru Enthusiast Forum > Accessories & Car Care > ICE
Reload this Page >

Getting a power cable into the boot - how?

Notices
ICE Serious sounds for serious cars.

Getting a power cable into the boot - how?

Old 11 October 2018, 02:01 PM
  #1  
Jay kay
Scooby Regular
Thread Starter
 
Join Date: Oct 2016
Location: Hertfordshire
Posts: 237
Default Getting a power cable into the boot - how?

I'm trying to run a fairly small power cable from the battery through to the boot, preferably via the passenger side of the car. For the life of me I cant find anywhere to go through the firewall. Am I missing something obvious?

Thanks in advance
Jay kay is offline  
Old 11 October 2018, 03:29 PM
  #2  
BrownPantsRacing
Scooby Regular
iTrader: (6)
 
BrownPantsRacing's Avatar
 
Join Date: Oct 2010
Location: Herts & Bucks
Posts: 7,703
Default

Yep, I managed to run a massive power cable from the battery to the boot in my car without issue.

Have a look at the bulkhead inside the engine bay on the passenger side, you'll see a lovely big wiring sealing grommet where all the engine bay wire goes through towards the ECU and fuse box area by the passengers feet. You can run the wire along the existing loom and cable tie it to the loom then either pull the wire through the existing grommet or push a tiny hole on the underside of the grommet for the wire to go through. If you do it that way just ensure the wire angles upwards slightly as it goes into the grommet so any water drips away from the grommet and not down through the grommet into the footwell.

You'll need to pull the carpet forward and get onto your back to look up behind the glove box but you will eventually see the wire coming through. Once inside the car you can pull all the plastic trim sections off the inside of the door foot step and run the wire along there with the existing wiring loom. Don't be scared to do this they all come off and go back together just fine. You may have to unbolt the seatbelt from what I remember to get them off and through. Once they pop out of the rear door step trim you can go straight under the rear seat (which is only 2 bolts to remove) and into the boot area under the carpet.

Simples!
BrownPantsRacing is online now  
Old 11 October 2018, 03:43 PM
  #3  
TECHNOPUG
Scooby Regular
iTrader: (1)
 
Join Date: Nov 2014
Location: Tetbury
Posts: 1,419
Default

Alternatively you can run the cable across the bulkhead and there is a grommet up above the turbo which you can use. Access is easier from inside the car as you only need to remove the lower trim and then you can see the cable enter by the steering column/clutch peddle.

Last edited by TECHNOPUG; 11 October 2018 at 03:45 PM.
TECHNOPUG is offline  
Old 12 October 2018, 10:56 PM
  #4  
Jay kay
Scooby Regular
Thread Starter
 
Join Date: Oct 2016
Location: Hertfordshire
Posts: 237
Default

Thanks for the advice. I went through drivers side in the end as that's where my defi cables go through. Probably for the best to keep power away from the RCA cables.
Jay kay is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
GB270_CALUM
ICE
3
22 May 2016 12:40 PM
millzy555
General Technical
5
25 July 2008 09:42 PM
spectrum48k
Non Scooby Related
9
19 April 2008 12:23 AM
jiffthejiffmanjaffa
ICE
23
28 January 2008 05:14 PM
ADP
Computer & Technology Related
11
02 December 2002 08:35 PM


Thread Tools
Search this Thread
Quick Reply: Getting a power cable into the boot - how?


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.