Notices

Little help with brakes

Thread Tools
 
Search this Thread
 
Old 04 November 2018, 08:34 PM
  #1  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default Little help with brakes

Hi I fitted some 4 pots to my other car and new lines and rear calipers iv bled the brakes a few times but they just don't feel right , there not spongy and have a great bite it's just when I'm braking hard from say 70 they don't seem to stop very well it's like the pedal doesn't want to go down anymore but I need it to has anyone experienced anything like this
Old 04 November 2018, 08:55 PM
  #2  
1509joe
Scooby Regular
iTrader: (2)
 
1509joe's Avatar
 
Join Date: Jan 2009
Location: Not sure
Posts: 3,294
Received 278 Likes on 248 Posts
Default

Specs
Old 04 November 2018, 08:58 PM
  #3  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default

08 civic type r fitted new disks pads all round new calipers and s/s lines on front got 4 pots with ds2500 pads
Old 04 November 2018, 09:01 PM
  #4  
1509joe
Scooby Regular
iTrader: (2)
 
1509joe's Avatar
 
Join Date: Jan 2009
Location: Not sure
Posts: 3,294
Received 278 Likes on 248 Posts
Default

ABS can be a pain to bleed on them sometimes you have to cycle the abs pump.
Old 04 November 2018, 09:04 PM
  #5  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default

Ok thanks I did bleed it about 5 times with engine ruining , could there still be air in the system or could be a bad booster , the pedal feels good until you feel you need to brake harder and it doesn't want go down any more but it only feels like it's half way down
Old 04 November 2018, 09:32 PM
  #6  
1509joe
Scooby Regular
iTrader: (2)
 
1509joe's Avatar
 
Join Date: Jan 2009
Location: Not sure
Posts: 3,294
Received 278 Likes on 248 Posts
Default

Get in pump pedal till it goes hard then start the engine and see does the brake pedal drop to see if your servo is working then check the one way valve between the servo and the inlet manifold.
Old 04 November 2018, 11:06 PM
  #7  
andy10v
Scooby Newbie
 
andy10v's Avatar
 
Join Date: Oct 2018
Location: Stirling
Posts: 17
Likes: 0
Received 1 Like on 1 Post
Default

Did you check piston sizes?
Old 05 November 2018, 09:11 PM
  #8  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default

Ok thanks mate I will give that ago , I dint check sizes but I'm sure I had this problem when I had the oe brakes
Old 11 November 2018, 10:36 AM
  #9  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default

Hi I did a few checks today I pumped the pedal until it went hard then turned on the car and the pedal did drop a bit I also sprayed some soapy water around the master cylinder and saw no bubbles and I checked the hose but couldn't see any rips or damage, any ideas what it could be
Old 11 November 2018, 10:50 AM
  #10  
TECHNOPUG
Scooby Regular
iTrader: (1)
 
TECHNOPUG's Avatar
 
Join Date: Nov 2014
Location: Tetbury
Posts: 1,968
Received 96 Likes on 79 Posts
Default

On the Impreza you need to trigger ABS whilst driving to cycle the pump. Then rebleed and you should expel some more air - usually the rear right if doing it in sequence as per manual. Honda maybe similar
Old 11 November 2018, 11:25 AM
  #11  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default

Ok thanks mate so would I need to go out do some hard braking then come back and bleed them , would the pedal feel spongy tho
Old 11 November 2018, 11:34 AM
  #12  
1509joe
Scooby Regular
iTrader: (2)
 
1509joe's Avatar
 
Join Date: Jan 2009
Location: Not sure
Posts: 3,294
Received 278 Likes on 248 Posts
Default

Yes the pedal will feel spongy you might find you need to get it on a diagnostic machine to cycle the ABS pump. Pressure bleeding at a low pressure and pump the pedal works sometimes but it will probably be a garage job too as people don't generally have them lying about
Old 11 November 2018, 12:04 PM
  #13  
seanvx
Scooby Regular
Thread Starter
 
seanvx's Avatar
 
Join Date: Sep 2016
Location: kent
Posts: 380
Likes: 0
Received 4 Likes on 4 Posts
Default

Ok thanks lads I might just take it to a garage , the pedal feels nice and hard no spongey feeling just to check when bleeding do you start from the furthest away from master cylinder so rear passenger and end up at front drivers and as the 4 pots have 2 nipples do the inside one first then outside and does it make a difference with engine on or off
Old 11 November 2018, 12:14 PM
  #14  
1509joe
Scooby Regular
iTrader: (2)
 
1509joe's Avatar
 
Join Date: Jan 2009
Location: Not sure
Posts: 3,294
Received 278 Likes on 248 Posts
Default

Generally yes to all the above. The furthest away option was the way I was taught but certain manufacturers seem to have their own ideas. Think this came abut with ABS systems. As for the fronts I just keep going till there's no air for it doesn't seem to matter if you do it by the book you still get a bit of air out of the other side
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Aztec Performance Ltd
Trader Announcements
34
06 July 2011 10:14 PM
Aztec Performance Ltd
Group Buys
3
19 October 2010 06:54 PM
The Grift
Wheels, Tyres & Brakes
2
18 December 2004 08:10 PM
WRX_Rich
Wheels, Tyres & Brakes
1
29 October 2004 06:40 PM



Quick Reply: Little help with brakes



All times are GMT +1. The time now is 01:17 AM.