Granby - YHPM

Cheers

Terry

 

Jim

YHPM - what model car is yours??

Cheers

Terry

 

Terry PM'd you back.

MY99



Jim

 

Am I too late??

Also could someone send me a PM stating all the details inc. expected dates of re-map etc, location etc.

 

Whohoo - another one added

Revised List

1. terryb
2. svvg
3. stevef
4. spufus
5. markyboy uk!
6. Bernard
7. Jim Litten
8.
9.
10.


Come on Guys - only 3 more places to fill.... what you waiting for??

 

GAZZER

YHPM

 

Tasberley

YHPM

 

Count me in...

 

terryb YHPM

 

1. terryb
2. svvg
3. stevef
4. spufus
5. markyboy uk!
6. Bernard
7. Jim Litten
8. Markwrx02
9. Brother of Markwrx02
10. Twigkiller

There's room for more - so keep adding your details or email me at terry.buckel@btopenworld.com

Cheers

Terry

 

1. terryb
2. svvg
3. stevef
4. spufus
5. markyboy uk!
6. Bernard
7. Jim Litten
8. Markwrx02
9. Brother of Markwrx02
10. Twigkiller
11. Jon17

There's room for more - so keep adding your details or email me at terry.buckel@btopenworld.com

Cheers

Terry

 

Looks like we're laughin' Terry

 

cuz one dropped out..

1. terryb
2. svvg
3. stevef
4. spufus
5. markyboy uk!
6. Bernard
7. Jim Litten
8. Markwrx02
9. Brother of Markwrx02
10. Twigkiller

There's still room for more - so keep adding your details or email me at terry.buckel@btopenworld.com

Cheers

Terry

 

Did you check it again?

 

1. terryb
2. svvg
3. stevef
4. spufus
5. markyboy uk!
6. Bernard
7. Jim Litten
8. Markwrx02
9. Brother of Markwrx02
10. Twigkiller
11. Granby

 

Top

 

Top

List

1. terryb
2. svvg
3. stevef
4. spufus
5. markyboy uk!
6. Bernard
7. Jim Litten
8. Mikewrx02
9. Twigkiller
10. Granby


6 hours to go to add your details...

 

Markyboy, Terry,

You both have private mail.

Dean

 

Hi just a couple of questions about the group buy, where and when is Bob doing the mapping? When will payment be required? Also does it include fitting the boost solenoid? What is the total price all in please? Car is a MY99 Type R STI.

Thanks in advance

Chris

 

Marky boy,

YHPM

Dean

 

bttt

 

Tiss,

I'd email TerryB & see if you can still get in, the GB ended on 31st May.

Good luck

 

Let's bring this thread back to life as we will be getting the remaps done from next weekend - I'm in 1st next Saturday morning - looking forward to it...

Had my uprated fuel Pp (Walbro 255lt/hr) and FSE 1:1 Fuel Pressure regulator fitted along with a Green Panel filter and a knocklink too (Oh and I fitted an STI 8 steering wheel - but that's nowt to do with the remap)


I'll post my comments on this thread after the remap - mine is a P1 decatted with the above mods and soon to be Tek3'd ....

Cheers

Terry

 

Terry,

Who did you get your FSE from, and who fitted it ?

Is it a plug and play device or does it require setting up ?

 

FSE - How difficult are these to fit on the newage cars?

Where is the OE one located anyway? I would like to change this too before remap.

Mark.

 

I got the pump and FSE from Mark at Lateral Performance - it's advertised on Scoobyshop - near the bottom of the page - £195 for the pair including a presure guage and delivery - and he has them in stock but he doesn't accept card payment - well packaged and prompt delivery - also a knowledgeable bloke who will give you advice when speaking to him.

The fitting of the FSE was a complete Tw@t to do - took far longer than it should have due to difficulty in removing the lower securing screw for the original regulator. (for some bizarre reason Subaru decided to use cross headed screws rather than hexagonal headed bolts - it's very difficult to get to and you can easily chew up the slots - as we did. Someone else on here mentioned that they had to remove the turbo - luckily we didn't have to do that.

Have a look at http://bbs.scoobynet.co.uk/showthread.php?t=223615 for a guide to fitting it - this is what I used.

Points of note - make the job easier for yourself by creating plenty of room - remove strut brace/ intercooler - it's easy enough and the turbo heat shield. Also I'd start by trying to remove the old regulator before you fit the new one - just in case you can't get it off. Use a ratchet/ cross-head drive and put plenty of pressure onto the screw head - or it won't turn. You can tap it lightly with a hammer - but the regulator is attached to the fuel rail that is attached to the injectors - so I wouldn't hit it too hard.

The original regulator is replaced with an adaptor and the FSE is secured at the other side of the intercooler. Another problem here is that the fuel hose that connects to the original regulator isn't quite long enough to fit the new adaptor - this caused a real pain as it is difficult to get access to the other end of the fuel pipe - but we did it and fitted a new length of pipe - cut a section off the fuel pipe supplied with the kit.

When refitting the adaptor use small bolts instead of the stupid screws - I don't know what size they are.

Bob Rawle has recommended that you set the FSE to 2.6 bar at hot idle.

The fuel pump is a doddle to fit - mine is a P1 and I removed the rear seat for ease of access - it is located under the boot carpet on the drivers side behind the rear seat.

I hope this helps - I'm sure it'll be worth it.

 

See you there Terry, i am in Saturday afternoon... can`t wait. Likewise i will post my views on the map. I have a MY99 WRX with full de-cat, k+n 57i and hopefully Sti intercooler. Speak to you all soon!!!

 

2 and a half days to go.....

 

Tell us how it goes matey!
I'm in for 14th of August and can't wait !!!

 

you bet I will