IMPREZA FOR SALE - 2003 Engine Tuner 550bhp (Hardly used)
#1
Scooby Newbie
Thread Starter
Join Date: Feb 2013
Location: Lancashire
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
IMPREZA FOR SALE - 2003 Engine Tuner 550bhp (Hardly used)
I bought this car about a year ago from Steve Paynter (SteveP 360 on here). Steve had done a lot of work to the car, including interior, suspension and engine work (which was carried out by Alan & Martin Jeffries of Engine Tuner). Here is a link to the thread that details all the work that Steve carried out :
https://www.scoobynet.com/projects-4...5r-billet.html
I had been looking around for the right car for quite a while and had viewed a lot of cars that looked and sounded great in their advert, but left a lot to be desired in the flesh. I'm quite finicky when it comes to cars so wanted to persevere and buy the right one. This one was actually better than I thought the advert presented it and I didn't take long to make my mind up to buy it.
Shortly after buying the car, one of the engine parts failed and I had to replace the full engine, adding an oil cooler and a few other bits at the same time. This cost me in the region of £9k and is now (motor wise) better than when I bought her. I wanted the best of everything and took the car back to Engine Tuner to have all the work carried out as they knew the car and (in my opinion) are one of the best around.
Alan and Martin did an excellent job of building the motor and Alan himself ran the car in for me. Since getting her back, I have only done about 120 miles. The reason for this is a serious lack of time due to work commitments (and a few other toys).
Here is the spec - please feel free to ask any questions and I will do my best to answer them. Alan or Martin Jeffries have also said that they would be happy to answer any more technical questions that I struggle with :
Under the bonnet
EJ22T Closed Deck Block Stroked to 2.35
Heat treated crank
Mahle pistons with uprated pins
Cosworth rods
ACL Race bearings
Rear thrust machining
Rebore and hone
Kevlar cam belt
RCM Group N Sump
RCM oil pump
Head stud kit 14 MM
Water pump
Tensioner & pulley kit
RCM head gaskets
Subaru gasket and seal kit
Helix Twin Plate clutch
Full RCM Twisted turbo Up/Downpipe kit ceramic coated
Garret GT35R Billet Ver 3 with clipped wheel Turbo
Tial 44mm External waste gate
GT Spec headers
Full RCM Track attack catch can with blow by breathing
Revolution 3inch exhaust system
RCM Twisted Turbo water supply kit
RCM Twisted Turbo Oil supply
RCM Twisted Oil drain Kit
RCM header relocation tank kit
RCM 100mm Spun Aluminium Trumpet
RCM Fuel Pressure regulator
K&N Cone Filter
RCM 15 Degree 100mm Silicone Hose (Black)
APS DR725 Front Mount Intercooler (Red Pipework)
3 port boost solenoid
Making 554.2bhp/520lbs on Vpower (1.9bar)
Heads
JDM Big port Heads with Head throat and seat work porting
Kelford 264 Cams
Cosworth Inconel +1mm valves
Fueling
Deatschwerks injectors
Perrin Fuel Rails
Bosch 44 Pump on Litchfield 1ltr Swirl pot
Walbro 255ltr in tank lift
Fuel filter
Fuel Pressure Sensor
Management
Syvecs PNP ECU
Toucan Touchscreen CAL Selection
Mapped By Martyn Jeffery (Enginetuner)
Wideband Lamda
DEFI Sti Genome Gauges (Turbo, Oil Pressure, Oil Temperature)
Fuel Pressure gauge
Brakes
AP 355 7040 Front Brake kit in Black (Brand new discs - 50 miles)
Brembo rear colour matched setup with Tarox disks and pads.
Braided Fuel Lines
DOT6 racing fluid
Suspension
AST Coilovers
Whiteline rear ARB 22mm
Anti lift Kit
Revolution Strut Brace
Cosmetics
Prodrive P1-WRC in satin black18 inch wheels ET46
Full Spec C interior incl Seats, Dash, Steering wheel and Carpet.
Damd flat bottom Steering wheel.
Zunsport Grills (Upper and Lower)
RCM Cool Panel Guide For Radiator
Detango'd Headlights
Although the car is over 10 years old, it's only really the shell & chassis that's this age - pretty much everything else is new.
She really is in immaculate condition and is lovely to drive. A lot of cars with this type of power are a bit of a pig to drive on the road and very on/off when it comes to power delivery. My mum has driven it a number of times (she's 72) and actually loves it (I turn the boost down to 1 bar for her though !)
Thanks for looking and I am confident in saying that she is one of the finest examples for her age that you will find.
Apologies, but I can't seem to upload any photos. Until I figure it out, please go to the eBay advert to view photos :
item number 291266166614
I'm looking for £17k for the car - this is what I paid for her last year and I have fitted a brand new engine & internals, oil cooler and a few other bits (at a cost of around £9k). I'm pretty firm on this price.
Thanks
Oliver.
https://www.scoobynet.com/projects-4...5r-billet.html
I had been looking around for the right car for quite a while and had viewed a lot of cars that looked and sounded great in their advert, but left a lot to be desired in the flesh. I'm quite finicky when it comes to cars so wanted to persevere and buy the right one. This one was actually better than I thought the advert presented it and I didn't take long to make my mind up to buy it.
Shortly after buying the car, one of the engine parts failed and I had to replace the full engine, adding an oil cooler and a few other bits at the same time. This cost me in the region of £9k and is now (motor wise) better than when I bought her. I wanted the best of everything and took the car back to Engine Tuner to have all the work carried out as they knew the car and (in my opinion) are one of the best around.
Alan and Martin did an excellent job of building the motor and Alan himself ran the car in for me. Since getting her back, I have only done about 120 miles. The reason for this is a serious lack of time due to work commitments (and a few other toys).
Here is the spec - please feel free to ask any questions and I will do my best to answer them. Alan or Martin Jeffries have also said that they would be happy to answer any more technical questions that I struggle with :
Under the bonnet
EJ22T Closed Deck Block Stroked to 2.35
Heat treated crank
Mahle pistons with uprated pins
Cosworth rods
ACL Race bearings
Rear thrust machining
Rebore and hone
Kevlar cam belt
RCM Group N Sump
RCM oil pump
Head stud kit 14 MM
Water pump
Tensioner & pulley kit
RCM head gaskets
Subaru gasket and seal kit
Helix Twin Plate clutch
Full RCM Twisted turbo Up/Downpipe kit ceramic coated
Garret GT35R Billet Ver 3 with clipped wheel Turbo
Tial 44mm External waste gate
GT Spec headers
Full RCM Track attack catch can with blow by breathing
Revolution 3inch exhaust system
RCM Twisted Turbo water supply kit
RCM Twisted Turbo Oil supply
RCM Twisted Oil drain Kit
RCM header relocation tank kit
RCM 100mm Spun Aluminium Trumpet
RCM Fuel Pressure regulator
K&N Cone Filter
RCM 15 Degree 100mm Silicone Hose (Black)
APS DR725 Front Mount Intercooler (Red Pipework)
3 port boost solenoid
Making 554.2bhp/520lbs on Vpower (1.9bar)
Heads
JDM Big port Heads with Head throat and seat work porting
Kelford 264 Cams
Cosworth Inconel +1mm valves
Fueling
Deatschwerks injectors
Perrin Fuel Rails
Bosch 44 Pump on Litchfield 1ltr Swirl pot
Walbro 255ltr in tank lift
Fuel filter
Fuel Pressure Sensor
Management
Syvecs PNP ECU
Toucan Touchscreen CAL Selection
Mapped By Martyn Jeffery (Enginetuner)
Wideband Lamda
DEFI Sti Genome Gauges (Turbo, Oil Pressure, Oil Temperature)
Fuel Pressure gauge
Brakes
AP 355 7040 Front Brake kit in Black (Brand new discs - 50 miles)
Brembo rear colour matched setup with Tarox disks and pads.
Braided Fuel Lines
DOT6 racing fluid
Suspension
AST Coilovers
Whiteline rear ARB 22mm
Anti lift Kit
Revolution Strut Brace
Cosmetics
Prodrive P1-WRC in satin black18 inch wheels ET46
Full Spec C interior incl Seats, Dash, Steering wheel and Carpet.
Damd flat bottom Steering wheel.
Zunsport Grills (Upper and Lower)
RCM Cool Panel Guide For Radiator
Detango'd Headlights
Although the car is over 10 years old, it's only really the shell & chassis that's this age - pretty much everything else is new.
She really is in immaculate condition and is lovely to drive. A lot of cars with this type of power are a bit of a pig to drive on the road and very on/off when it comes to power delivery. My mum has driven it a number of times (she's 72) and actually loves it (I turn the boost down to 1 bar for her though !)
Thanks for looking and I am confident in saying that she is one of the finest examples for her age that you will find.
Apologies, but I can't seem to upload any photos. Until I figure it out, please go to the eBay advert to view photos :
item number 291266166614
I'm looking for £17k for the car - this is what I paid for her last year and I have fitted a brand new engine & internals, oil cooler and a few other bits (at a cost of around £9k). I'm pretty firm on this price.
Thanks
Oliver.
Last edited by RITSON; 12 October 2014 at 06:24 PM.
Trending Topics
#8
Scooby Newbie
Thread Starter
Join Date: Feb 2013
Location: Lancashire
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the comments - she really is a lovely car. Anybody that has met Steve Paynter will know how meticulous he is with his cars.
Yes, Jazzy's right - she threw a rod. Alan specced a different make of rods for the rebuild and added an oil cooler as a safety precaution too.
Yes, Jazzy's right - she threw a rod. Alan specced a different make of rods for the rebuild and added an oil cooler as a safety precaution too.
#9
Scooby Regular
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
Naturally, I can't offer any kind of guarantees with this, but I'm happy to say that everything said about this car is correct.
The original I beam rod failed, and of course there is no warranty from the makers. Everything built into the new block is spot on.
You certainly couldn't build this for anywhere near the money, and I'd like to think somebody will pick this one up and really enjoy it.
The original I beam rod failed, and of course there is no warranty from the makers. Everything built into the new block is spot on.
You certainly couldn't build this for anywhere near the money, and I'd like to think somebody will pick this one up and really enjoy it.
#10
Scooby Regular
iTrader: (6)
Join Date: Oct 2008
Location: Nottingham
Posts: 1,264
Likes: 0
Received 0 Likes
on
0 Posts
Naturally, I can't offer any kind of guarantees with this, but I'm happy to say that everything said about this car is correct.
The original I beam rod failed, and of course there is no warranty from the makers. Everything built into the new block is spot on.
You certainly couldn't build this for anywhere near the money, and I'd like to think somebody will pick this one up and really enjoy it.
The original I beam rod failed, and of course there is no warranty from the makers. Everything built into the new block is spot on.
You certainly couldn't build this for anywhere near the money, and I'd like to think somebody will pick this one up and really enjoy it.
From my personal view if ET have built it, then second to none!
My old 500/500 Prodrive classic is still doing the rounds 6/7 years after build👌
ET
#12
Scooby Newbie
Thread Starter
Join Date: Feb 2013
Location: Lancashire
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Alan
sorry to see her go really, but I'll still have the Hawkeye to keep me entertained.
Out of interest, I did a few rolling starts against a mate's GTR R35 (Lichfield Stage 1 mapped to appx 580bhp) - one from 30mph, one from 50mph and one from 70mph. All done on private land of course !
The Scooby won all 3 - convincingly.
sorry to see her go really, but I'll still have the Hawkeye to keep me entertained.
Out of interest, I did a few rolling starts against a mate's GTR R35 (Lichfield Stage 1 mapped to appx 580bhp) - one from 30mph, one from 50mph and one from 70mph. All done on private land of course !
The Scooby won all 3 - convincingly.
#16
Scooby Regular
iTrader: (84)
Thanks Alan
sorry to see her go really, but I'll still have the Hawkeye to keep me entertained.
Out of interest, I did a few rolling starts against a mate's GTR R35 (Lichfield Stage 1 mapped to appx 580bhp) - one from 30mph, one from 50mph and one from 70mph. All done on private land of course !
The Scooby won all 3 - convincingly.
sorry to see her go really, but I'll still have the Hawkeye to keep me entertained.
Out of interest, I did a few rolling starts against a mate's GTR R35 (Lichfield Stage 1 mapped to appx 580bhp) - one from 30mph, one from 50mph and one from 70mph. All done on private land of course !
The Scooby won all 3 - convincingly.
#17
Scooby Newbie
Thread Starter
Join Date: Feb 2013
Location: Lancashire
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
11 January 2021 03:08 PM
ATWRX
Full Cars Breaking For Spares
88
01 February 2016 07:28 PM
Scott@ScoobySpares
Full Cars Breaking For Spares
7
14 December 2015 08:16 AM