MeisterR 20% OFF Coilovers Group Buy
#97
I know that i can still get them , and with the forum discount aswell , but they have none available and was also talking with Jerrick about another group buy but have yet to hear back.
#104
First impressions are great! I have set all four to 10 clicks from soft, and it is comfortable and responsive. Only done 20 miles so far, so can't really say more than that at the moment.
#106
Sounds good then so far , keep us updated once youve got some more miles on them bud . Still trying to get some info on when they will be available again but not having much luck ...
Last edited by Andyd1888; 24 June 2016 at 01:44 PM.
#107
The acid test is when SWMBO gets in! Actually I'm pretty confident she'll be fine. The HSDs I had before were set to as soft as they could go, and were far too stiff and bouncy. On the MeisterRs I am starting with 10 clicks and have some room to manoeuvre if she thinks they're still too firm
#109
Scooby Regular
iTrader: (3)
The acid test is when SWMBO gets in! Actually I'm pretty confident she'll be fine. The HSDs I had before were set to as soft as they could go, and were far too stiff and bouncy. On the MeisterRs I am starting with 10 clicks and have some room to manoeuvre if she thinks they're still too firm
#110
The missus had her first ride in the car over the weekend and was happy: 'They are still firm but much better' and didn't complain at all!
Went to get geo setup done and they couldn't free up the rear toe adjustment nuts, so have to go back in a week after adding some more penetrating lubricant to the nuts and see if they can adjust the rear end. They also didn't want to add as much negative camber as I asked for, but at least said I could come back and they'd adjust it for free if I didn't like it at the factory settings.
What settings did you go for Stuart?
#111
Scooby Regular
iTrader: (3)
Glad to hear you're enjoying them!
I took along these settings, copied from bonesetter on an old thread on here.
Then they were tweaked from there. I was lucky in that I found a good garage with a lot of experience in setting up cars (they've got their own race team).
I took along these settings, copied from bonesetter on an old thread on here.
Then they were tweaked from there. I was lucky in that I found a good garage with a lot of experience in setting up cars (they've got their own race team).
#112
Glad to hear you're enjoying them!
I took along these settings, copied from bonesetter on an old thread on here.
Then they were tweaked from there. I was lucky in that I found a good garage with a lot of experience in setting up cars (they've got their own race team).
I took along these settings, copied from bonesetter on an old thread on here.
Then they were tweaked from there. I was lucky in that I found a good garage with a lot of experience in setting up cars (they've got their own race team).
Either way, I went out to the garage last night to adjust the ride height, and could only get the locking rings undone on two wheels, so I have a wonky wagon at the moment! Have to either go back to the lower setting on the ones I did adjust, or find some way to undo the locking rings on the nearside wheels. They've only been on the car a couple of weeks so I wasn't expecting them to be jammed already
#114
Isn't it more hassle to buy and fit a roll-centre correction kit than to change the ride height and re-do the alignment? I am trying to raise my ride height to avoid needing roll-centre correction!
#115
OK, Edwin sent me out some replacement spanners and I got the rings freed up, so I have raised the ride height back to a more normal setting. Will be getting the alignment re-done on Friday.
Thread
Thread Starter
Forum
Replies
Last Post
Danny0608
Subaru
6
27 September 2015 02:16 PM
Danny0608
Subaru Parts
0
12 September 2015 02:59 PM